Skip to main content

MEO Class 2

Safety:
  • Purpose of Torsion box with sketch
  • Transverse section of container ship
  • Stresses on ship ( hogging, sagging, tensile, compressive)
  • State objective of Ism in detail.
  • Discharge criteria for sewage.
  • Special area for annex 1,4,5,6
  • Latest amendments in Annex 6
  • Why ship required class?
  • Antifouling convention?

Motor:
  • Types of crankshaft. Explain construction of each type with sketch and material used
  • Iron-carbon phase diagram.
  • Drop test of exhaust valve
  • Draw tandom piston and state adv. and disadvantage of using it.
  • Draw and explain propeller curve.
  • Lost motion in RTA? Why it's required?
  • How servomotor works?
  • Development in RTA
  • MC vs MCC
  • MAN vs Sulzer
  • Bearings in Main engine and lubrication
  • Cylinder lubrication in MAN and Sulzer
  • Fatigue, creep and fretting in main engine
  • What is CCA?
Electrical:
  • Difference between home supply and ship supply
  • How will you measure voltage in 3 pin of your household socket with multimeter and what value you will get on multimeter.
  • what is LV and HV, Is 2000V d.c is high voltage ?
  • There is no marking (u1,v1...u2,v2... ) on six terminal of an old induction motor. how you will identify the two end of coils and connect it in delta. Explain through sketch.
  • Explain 3 phase neutral insulated and earthed system and there advantages.
  • Types of fault on circuit.
  • Difference between closed circuit and short circuit with help of numerical example.
  • How to check charge of a Lead Acid battery.

MEP:
  • How to check trueness of bend pump shaft.
  • If shaft is bent and you have to use same shaft how you will use it.
  • Where to put shims in air compressor and its purpose. Draw and explain
  • Belt driven purifier clutch mechanism. Draw how clutch shoe is arranged in the same.
  • Type and purpose of accumulator in reciprocating pump. explain in full detail.
  • why oil separator is fitted after LP side in refrigeration system.

Comments

Popular posts from this blog

Difference Between A, B & C-Class Divisions?

IMO Symbol A Class Division  IMO Symbol B Class Division  SOLAS has tables for structural fire protection requirement of bulkheads and decks. The requirements depend on the spaces in question and are different for passenger ships and cargo ships. The Administration has required a test of a prototype bulkhead or deck in accordance with the Fire Test Procedures Code to ensure that it meets the above requirements for integrity and temperature rise. Types of Divisions: "A" Class "B" Class "C" Class "A" Class: "A" class divisions are those divisions formed by bulkheads and decks which comply with the following criteria: They are constructed of steel or equivalent material They are suitably stiffened They are constructed as to be capable of preventing the passage of smoke and flame to the end of the one-hour standard fire test. they are insulated with approved non-combustible materials such that the average tempera

Why do we blow through engine before starting ?

The engine is blown through on air before starting it : a) To Blow out through indicator cock any residual exhaust gas or     other products of combustion trapped inside the cylinder after     shutting the engine. b) To check if any jacket cooling water from cylinder head or     turbocharger or any other source, has leaked while the engine          was shut and collected on top of piston. If while blowing                  through, water comes out of indicator cock or relief valve, we          need to investigate and rectify the fault before starting the                engine. It is imperative that the engine is blown through before        starting. There have been cases where the generator engine has        been started from control room without bothering to blow     through first, and water collected on top of piston has resulted in      a bent connecting rod and broken piston.( Reason – water can          not be compressed )

Load Line & Why it is Important

Merchant ships have a marking on their hull know as the Plimsoll line or the Plimsoll mark, which indicates the limit until which ships can be loaded with enough cargo, internationally, the Plimsoll line on a ship is officially referred to as the international load line. Every type of ship has a different level of floating and the Plimsoll line on a ship generally varies from one vessel to another.  All vessels of 24 meters and more are required to have this Load line marking at the centre position of the length of summer load water line. There are two types of Load line markings:- Standard Load Line marking – This is applicable to all types of vessels. Timber Load Line Markings – This is applicable to vessels carrying timber cargo. These marks shall be punched on the surface of the hull making it visible even if the ship side paint fades out. The marks shall again be painted with white or yellow colour on a dark background/black on a light background.  The comp